Navigation: Home > Our Products

Our Products

Please Contact Kim Reynolds For Current Pricing
Phone: 785-275-2384
Email: kim@tankerectiontools.com

HEAVY DUTY KEYPLATE

HEAVY DUTY KEYPLATE

Heavy duty keyplate is a time tested design used in the industry for years. Constructed out of ½” carbon steel it is able to handle all ranges of thicknesses for tank construction.

Part#: KP0001
Material: Carbon Steel
Height: 4.25” — Width: 5.5” — Length: 19.25” — Weight: 17.3

LIGHT DUTY KEYPLATE

LIGHT DUTY KEYPLATE

Light duty keyplate is based on the same design as our heavy duty keyplate but constructed out of 3/8” carbon steel. Weighing in at just under 13#, it is a great choice for smaller tanks and top rings.

Part#: KP0002
Material: Carbon Steel
Height: 4.25” — Width: 5.5” — Length: 19.25” — Weight: 12.7

90º FIXED KEYPLATE

90º FIXED KEYPLATE

90º Key Plate works at a 90º angle to push and pull walls as well as raise and lower. 90º fixed keyplate has a low profile design.

Part#: KPF001
Material: Carbon Steel
Height: 8” — Width: 6.5” — Length: 8” — Weight: 12.7

90º HINGED KEYPLATE

90º HINGED KEYPLATE

Great choice for numerous fitting such as wind girder and cone sections where fit up is needed allowing to continue to push and pull.  It features 110° to flat full range of motion.

Part#: KPH001
Material: Carbon Steel
Height: 1-1/2” — Width: 5-1/2” — Length: 18-3/16” — WEIGHT: 19.0

BLANK ERECTION NUTS: CARBON STEEL

BLANK ERECTION NUTS: CARBON STEEL

Erection nuts are burned, machined and drilled with 1-1/8” diameter holes.  Various sizes available

Part#: en38 — (2”x2”x3/8”)
(Carbon Steel) Weight: 0.2 - Width: 2” - Thickness: 3/8” - Length: 2”

Part#: en12 — (2”x2”x1/2”)
(Carbon Steel) Weight: 0.3 - Width: 2” - Thickness: 1/2” - Length: 2”

Part#: en34 — (2”x2”x3/4”)
(Carbon Steel) Weight: 0.6 - Width: 2” - Thickness: 3/4” - Length: 2”

Part#: en01 — (2”x2”x1”)
(Carbon Steel) Weight: 0.9 - Width: 2” - Thickness: 1” - Length: 2”

BLANK ERECTION NUTS: STAINLESS STEEL

BLANK ERECTION NUTS: STAINLESS STEEL

Erection nuts are burned, machined and drilled with 1-1/8” diameter holes.  Various sizes available.

Part#: ens38 — (ss 2”x2”x3/8”)
(304 Stainless Steel) Weight: 0.9 - Width: 2” - Thickness: 3/8” - Length: 2”

Part#: ens12 — (ss 2”x2”x1/2”)
(304 Stainless Steel) Weight: 0.3 - Width: 2” - Thickness: 1/2” - Length: 2”

Part#: ens34 — (ss 2”x2”x3/4”)
(304 Stainless Steel) Weight: 0.6 - Width: 2” - Thickness: 3/4” - Length: 2”

Part#: ens01 — (ss 2”x2”x1”)
(304 Stainless Steel) Weight: 0.9 - Width: 2” - Thickness: 1” - Length: 2”

U-BAR

U-BAR

U-bar is constructed of carbon steel or stainless steel and features an angled pin slot that allows the bull pin to stay in place.

Part#: UB0001
(Carbon Steel) Weight: 0.9 - Height: 1-5/8” - Thickness: 5/8” - Length: 7-3/4”

Part#: UBs0001
(304 Stainless Steel) Weight: 0.9 - Height: 1-5/8” - Thickness: 5/8” - Length: 7-3/4”

KEY SHIM: CARBON STEEL

KEY SHIM: CARBON STEEL

Key shims are available in 3/32”, 1/8”, and 5/32” thicknesses and are constructed from carbon steel.  Our shims are designed to use the pin and wedge method allowing adjustment for several thicknesses of plate material.

Part#: KS332 — (3/32”)
(Carbon Steel) Weight: 0.1 - Width: 2” - Thickness: 3/32” - Length: 4”

Part#: KS18 — (1/8”)
(Carbon Steel) Weight: 0.1 - Width: 2” - Thickness: 1/8” - Length: 4”

Part#: KS10 — (10ga)
(Carbon Steel) Weight: 0.1 - Width: 2” - Length: 4” - Thickness: 10ga

Part#: KS532 — (5/32”)
(Carbon Steel) Weight: 0.1 - Width: 2” - Thickness: 5/32” - Length: 4”

KEY SHIM: STAINLESS STEEL

KEY SHIM: STAINLESS STEEL

Key shims are available in 3/32”, 1/8”, and 5/32” thicknesses and are constructed from stainless steel. Our shims are designed to use the pin and wedge method allowing adjustment for several thicknesses of plate material.

Part#: KS332S — (ss 3/32”)
(304 Stainless Steel) Weight: 0.1 - Width: 2” - Thickness: 3/32” - Length: 4”

Part#: KS18S — (ss 1/8”)
(304 Stainless Steel) Weight: 0.1 - Width: 2” - Thickness: 1/8” - Length: 4”

Part#: KS532S — (ss 5/32”)
(304 Stainless Steel) Weight: 0.1 - Width: 2” - Thickness: 5/32” - Length: 4”

KEY SHIM WEDGE

KEY SHIM WEDGE

Our wedges are a tapered design and fit snugly in the shim slot. Used with Key Shim and Shim Pin.

Part#: KWS0001
Material: Carbon Steel
Width: 2-1/2” — Thickness: 1/4” — Length: 9” — WEIGHT: 0.8


SHIM PIN

SHIM PIN

Shim has a strategically placed “stop” to prevent it from falling out of the key shim but allowing for an easier installation when used for girth seams.  Used with the Key Shim and Key Shim Wedge.

Part#: SP0001 (Carbon Steel)
Width: 3/4” — Length: 4” — WEIGHT: 0.5

Part#: SP0001s (304 Stainless Steel)
Width: 3/4” — Length: 4” — WEIGHT: 0.5

BRACKET STRAP

BRACKET STRAP

Used to adhere scaffolding to tanks, simply weld on and drop the scaffolding into the opening.  Constructed out of carbon steel or stainless steel, the bracket strap has the industry standard single tab style slot.  The double pin strap can be constructed upon request.

Part#: BS0001 (Carbon Steel)
Thickness: 1/4” — Width: 2” — Length: 10-1/8” — WEIGHT: 1.4

Part#: BS0001s (304 Stainless Steel)
Thickness: 1/4” — Width: 2” — Length: 10-1/8” — WEIGHT: 1.4

MONEY MAKER WEDGE

MONEY MAKER WEDGE

The Money Maker Wedge is a one-piece construction with a standard “nut” size of 2x2x1” with a 1-1/8” hole for attaching a rope or lanyard.

Part#: MM01
Material: Carbon Steel
Width: 5” — Height: 5” — Thickness: 2” — Length: 14” — WEIGHT: 8.5


BULL PIN

BULL PIN

Thorough testing on our bull pins was conducted to ensure the correct hardness and retention.  Machined out of special carbon steel alloy or stainless steel, our bull pin is extremely hard to fracture and will tolerate abuse.  It features a tapered head that slows the “mushrooming” that occurs after being used extensively.

Part#: BP0001 (Carbon Steel)
Width: 1-1/4” — Length: 12” — WEIGHT: 2.5

Part#: BP0001s (304 Stainless Steel)
Width: 1-1/4” — Length: 12” — WEIGHT: 2.5

KEY CHANNEL STRONGBACK

KEY CHANNEL STRONGBACK

Strong backs are designed to form a stiffener between to horizontal sheets to provide stability to each ring. The Key Channel Strong back is available in 4” or 6” inch design and constructed out of structural grade channel iron.  It features tabs to allow the bull pin to lock into place.

Part#: KC0002 (6” Carbon Steel)
Height: 2” — Width: 6” — Length: 48” — WEIGHT: 44.0

Part#: KC0001 (4” Carbon Steel)
Height: 1-1/12” — Width: 4” — Length: 48” — WEIGHT: 27

I-BEAM STRONGBACK

I-BEAM STRONGBACK

Constructed from carbon steel, the I-Beam is primarily used for wind protection and girth seam fit up applications.

Part#: SB0001
Material: Carbon Steel
Height: 3” — Width: 2-1/4” — Length: 48” — WEIGHT: 23.0


POISON PLATE

POISON PLATE

Made of 304 Stainless Steel, these plates eliminate carbon impregnation while tools are being used on Stainless Steel.  The Poison Plate reduce the cost of purchasing stainless steel key plates.

Part#: SB0001
Material: 304 Stainless Steel
WEIGHT: 0.1

FINGER BAR

FINGER BAR

Finger Bar is constructed of carbon steel and used for fitting applications to eliminate mismatch of shell sections. 1"x4"x3/8"

Part#: FB0001
Material: Carbon Steel
Width: 1” — Thickness: 3/8” — Length: 4” — WEIGHT: 0.5

SCAFFOLD BRACKET/POST

SCAFFOLD BRACKET/POST

Scaffold brackets and posts can be purchased galvanized or painted yellow. They are constructed out of carbon steel and feature the single tab design to match our bracket straps. Our posts are constructed of pipe and feature chain link cable supports.

Material: Carbon Steel
 
Part#: SBP001 — (Bracket-Yellow) Weight: 26

Part#: SPP001 — (Post-Yellow) Weight: 10

Part#: SBG001 — (Bracket-Galvanized) Weight: 26

Part#: SPG001 — (Post-Galvanized) Weight: 10

C-LUG

C-LUG

C Lug is constructed of ¾” carbon steel and is a good choice for welding to the shell for slotting in bottoms or replacing a new bottom

Part#: CL0001
Material: Carbon Steel
Width: 7-1/4” — Thickness: 3/4” — Length: 7-1/2” — WEIGHT: 10

STRONG BACK CLIPS

STRONG BACK CLIPS

Made out of 3/8” plate, this horseshoe shaped clip is 6” square and is used for attaching the strongback to the shell.

Part#: TT19
— WEIGHT: 3 lbs each

WELDER TEST PLATE - 1/2”

WELDER TEST PLATE - 1/2”

Made of ½” plate, welder test plates can be used for welder practice, tests and qualifications such as ASME. Sold per plate.

Part#: WTP0001 — WEIGHT: 3.4 lbs each
Width: 3” - Thickness: 1/2” - Length: 8” - Bevel: 22.5” - Land: 1/8”